DCC & DC

15V DC Power Adapter (1500mA Output, 100-240V AC Input) This high quality regulated switching power adapter powers any 15 Volt DC device up to 1.5 Amp. Made with quality in mind, this unit outperforms similar products. Let RR-CirKits keep your devices...

Logic level interface compatible with other standard RR-CirKits I/O modules. Boot Loader for user installable firmware upgrades. Includes powerful internal Logic Elements. Also compatible with JMRI. Small package size. Just 1-¾" x 3-1/4" x 5/8". POC...

May be used to provide the required termination at each end of the CAN bus LCC®  Balanced CAN termination provides the best noise rejection. Includes CAN bus Power Indicator and CAN bus data monitor for easy network cable trouble shooting. LCC requires...

Bit level repeater connects two LCC ® CAN bus segments. Quad RJ45 connectors for dual LCC ® CAN bus loop through connections. Includes a CAN bus data monitor LED for network trouble shooting. 2 LED display. Small package size. Just 2-1/2" x 3-1/2" x 1"...

Create a powered LCC bus for simple wiring by powering your LCC Nodes over the cable. The LCC Power-Point supplies 1/2A to each LCC CAN Bus cable.  PS-S-15-1200 universal switching power supply is included.  (Terminator and CAN bus cable shown are not...

The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot...

With the LokSound 5 Nano DCC, ESU has succeeded in developing an even smaller LokSound decoder: With only 19.6 mm x 8.5 mm x 3.2 mm, it is the smallest LokSound decoder we have ever built. Thus, it should really be used in all vehicles of nominal sizes N...

 The LokSound 5 micro DCC Direct Kato USA has been specially developed for installation in track N vehicles of the Kato USA brand: Most diesel locomotives of this manufacturer are installed in the American model of these decoders instead of the...

Stranded, 550 MHz, UTP, Pure Bare Copper Wire, 24AWG, 5ft, White.

Stranded, 550 MHz, UTP, Pure Bare Copper Wire, 24AWG, 1ft, White.

Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28 - AWG 12 so there is no problem connecting different wire sizes together. Easily disconnect wiring for trouble...

Servo Extension Cable (M-F) This 39" cable may be used to extend the length of the above (M-M) cables.

Servo Connection Cable (M-M) This 20" cable may be used to connect two Quik-Link devices.

This Breakout board allows easy solder free connections from up to 8 Quik-Link devices to 10 pin I/O cables using 3 wire servo style cables. Also compatible with Berrett Hill products.

The TAB is designed to provide a solder-less connection between the SMD-8 and Tortoise. It includes 10 pin daisy chain cable headers and channel selection jumpers. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. An 8...

The Button-QL is an LCC Sample Mode compatible indicator/switch unit. When used with an LCC node the switch function and indicator function may be controlled separately over the same I/O channel. The unit is configurable via solder jumpers on the back...

The Tortoise Quik-Link is a plug on Tortoise driver board. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. It connects directly to any LCC output port with a standard 10 pin ribbon cable or via a QL-Breakout using a...

This plastic mounting track is suitable for mounting six I/O modules to a flat surface. (3 1/2" x 12")

This plastic mounting track is suitable for mounting four I/O modules to a flat surface. (3 1/2" x 8")

This plastic mounting track is suitable for mounting three I/O modules to a flat surface. (3 1/2" x 6")