Bob Smith Industries

FINISH-CURE™ 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer...

IC-LOC™ Purple prevents loosening of small fasteners from normal use and vibration, but parts can still be disassembled with hand tools. IC-LOC™ Purple seals and prevents rusting of...

IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC Green™ wicks down into the threads of fasteners using capillary...

IC-LOC™ Red is a medium thickness, high strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Red™ is cured, the fasteners are permanently...

IC-LOC™ Blue is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Blue™ is cured, the fasteners can be...

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded...

INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray...

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like...

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like...

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and...

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and...

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and...

Insta-Flex+™ clear rubber toughened has similar qualities to our black IC-2000™ but can be used in applications where you do not want the adhesive to be seen. The carbon component of...

Insta-Flex™ flexible thin CA is ideal for many applications, including the installation of CA hinges. When cured, INSTA-FLEX™ does not turn brittle and remains clear, even if accelerated...

IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™...

IC-GEL™ is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE™...

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works...

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works...

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works...

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly...