Adhesives

7 applicatorsTHE GLUE LOOPER® is a micro glue applicator made for applying a VERY small amount of LOW VISCOSITY (i.e. - very thin) glue where you want it to go with very little or no trace of the glue.It uses capillary action with LOW VISCOSITY...

6 applicatorsTHE GLUE LOOPER® is a micro glue applicator made for applying a VERY small amount of LOW VISCOSITY (i.e. - very thin) glue where you want it to go with very little or no trace of the glue.It uses capillary action with LOW VISCOSITY...

4 small, 4 medium, 2 large applicatorsTHE GLUE LOOPER® is a micro glue applicator made for applying a VERY small amount of LOW VISCOSITY (i.e. - very thin) glue where you want it to go with very little or no trace of the glue.It uses capillary...

For those of you would like a hobby knife handle with your order we have them in stock! By popular request, the  green  GLUE LOOPER®  handle. Made in the USA. Soft green rubber handle with very easy to use tension clamp. Comes with a...

FINISH-CURE™ 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE™ can be sanded the easiest...

IC-LOC™ Purple prevents loosening of small fasteners from normal use and vibration, but parts can still be disassembled with hand tools. IC-LOC™ Purple seals and prevents rusting of threads.

IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC Green™ wicks down into the threads of fasteners using capillary action and has good performance even with oil coated...

IC-LOC™ Red is a medium thickness, high strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Red™ is cured, the fasteners are permanently together and cannot be disassembled. IC-LOC Red™ will...

IC-LOC™ Blue is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once the IC-LOC Blue™ is cured, the fasteners can be disassembled with standard hand tools if required.

UN-CURE™ debonder will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops of UN-CURE™ will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone...

INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from...

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s...

FOAM-CURE™ is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s...

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose...

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose...

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose...