DCC & DC

DCC Main Bus Wire, (Black), 14AWG, 50 Feet NCE Multi Scale DCC Main Bus Wire Black 50'

Male Quick Connect, (Red), package of 32, 18-22AWG NCE Multi Scale Male Quick Connects 32 Pack

Track Bus Taps, (Blue), package of 32, 14-16AWG NCE Multi Scale Track Bus Taps 32 Pack

Power Drop Wires, Red, package of 16, 16", 22AWG NCE Multi Scale Power Drop Wires Red 16 Pack

Power Drop Wires, Black, package of 16, 16", 22AWG NCE Multi Scale Power Drop Wires Black 16 Pack

Layout Wiring Kit, 100 Foot DCC power bus. DCC main bus wiring for typical 100 foot double track mainline. Includes: • Main Bus - 100 feet each red and black 14 AWG stranded wire • Feeder Wires - 32 each red and black feeder 22 AWG wires...

Same six-wire connectors in front as UTP but allows use of off-the-shelf CAT5 cables to connect panel-to-panel at rear. Can be used as a cab bus splitter and also adds the ability to add power to the cab bus for larger layouts.

The AR10 is an automatic reverse loop controller for DCC layouts. It requires just 4 connections, two to the main line and two to the loop. In addition it functions as a circuit breaker for the reverse loop. Recommended for DCC systems from 1 to 10Amps.

Build your control panels with greatly simplified wiring. Just connect push buttons to the Mini Panel and use to issue turnout routing macros, individual turnout commands by pushing one button. Set up is easy, just plug in a Pro Cab (sold separately) and...

Description: It is usually desirable to divide a layout into separate track power sections (power districts) so that a derailment or short circuit on one section of the layout doesn't shut down power to other sections. The CP6 can be used to divide the...

Provides short circuit protection for one power district. Can be used with most DCC systems.  This is not recommended for use with the PowerCab. For the PowerCab use a CP6!

Add this USB computer interface for computer programming and/or operation of your Power Cab equipped layout. Requires USB cable, computer and railroad computer program such as JMRI Decoder Pro and Panel Pro

Add a separate PCP panel to operate your PowerCab in other places or on other layouts. Use the P114 and you will only have to move the PowerCab.

13.8v DC Power Supply. 1.3 Amp / 2 amp peak. US approved power supply suitable for PowerCab and other applications. This plugs into the back of panels such as the PCP(PowerCab connection panel) and the UTP-CAT5

Decoder Test Kit. Perfect companion to DCC installation and operation. The decoder tester works with ANY DCC decoder. Test for motor forward and reverse, functions F0F, F0R, 1, and 2. A DCC system is required for functionality, the DTK acts as an...

This is our lowest cost, easiest to use cab bus panel. All four RJ-12 jacks are wired in parallel for easy plug and play use. This board also provides a convenient point to add additional 12 Volt cab bus power, just plug in a 12 Volt "wall wart" power...

Detects DCC current being drawn in a block. Connects to AIU01 or Mini Panel. Isolated so that there is no electrical connection to the track. Needs no external power for most operations, suitable for DCC power up to 20 Amps. Can light up LED or operate...

The Auxiliary Input Unit (AIU) provides a means of connecting external devices such as switch contacts, Block Detectors (BD20), or other sensors to the NCE Cab Bus or Command Station. These external devices can be anything that supplies an electrical...

Dimensions: 0.595" x 0.390" (15mm x 10mm)  Direct plug in to locos equipped with Next18 (NEM-662) socket  Features of this decoder: Silent Running(TM) Torque compensated motor drive Torque Compensation for ultra smooth low speed...

N Scale N14K2 Drop-In Control Only Decoder. Includes pre-soldered motor clips.