DCC & DC

4 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management. Each DS supports Occupancy detection. Each...

Features: Board replacement decoder for Atlas MP15 units Golden-White LEDs for added realism Decoder Lock equipped   Don’t settle for a decoder without the latest features in your locomotive! Upgrade your N Scale Atlas...

15V DC Power Adapter (1500mA Output, 100-240V AC Input) This high quality regulated switching power adapter powers any 15 Volt DC device up to 1.5 Amp. Made with quality in mind, this unit outperforms similar products. Let RR-CirKits keep your devices...

May be used to provide the required termination at each end of the CAN bus LCC®  Balanced CAN termination provides the best noise rejection. Includes CAN bus Power Indicator and CAN bus data monitor for easy network cable trouble shooting. LCC requires...

Bit level repeater connects two LCC ® CAN bus segments. Quad RJ45 connectors for dual LCC ® CAN bus loop through connections. Includes a CAN bus data monitor LED for network trouble shooting. 2 LED display. Small package size. Just 2-1/2" x 3-1/2" x 1"...

The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot...

With the LokSound 5 Nano DCC, ESU has succeeded in developing an even smaller LokSound decoder: With only 19.6 mm x 8.5 mm x 3.2 mm, it is the smallest LokSound decoder we have ever built. Thus, it should really be used in all vehicles of nominal sizes N...

 The LokSound 5 micro DCC Direct Kato USA has been specially developed for installation in track N vehicles of the Kato USA brand: Most diesel locomotives of this manufacturer are installed in the American model of these decoders instead of the...

Stranded, 550 MHz, UTP, Pure Bare Copper Wire, 24AWG, 5ft, White.

Stranded, 550 MHz, UTP, Pure Bare Copper Wire, 24AWG, 1ft, White.

Servo Extension Cable (M-F) This 39" cable may be used to extend the length of the above (M-M) cables.

Servo Connection Cable (M-M) This 20" cable may be used to connect two Quik-Link devices.

The Button-QL is an LCC Sample Mode compatible indicator/switch unit. When used with an LCC node the switch function and indicator function may be controlled separately over the same I/O channel. The unit is configurable via solder jumpers on the back...

(10 position IDC male with latch) Box of 10 Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension cables. Screw ears allow easy mounting to the layout.

(10 position IDC socket) Box of 25 Insulation Displacement Connectors for use with 10 wire flat ribbon cable.

(Fan Out Board, Dual Direct) This board is specifically designed to terminate the dual cable, eight stall motor, connections from a single SMD-8 board. It includes on board jumpers to select common positive or common negative for optional single ended...

Fan Out Board, Direct Drive) This board is specifically designed to direct drive eight LED's from a single RR-CirKits port. It includes on board locations for current limiting resistors and jumpers to select common anode or common cathode connections. No...

This board is normally used for block detection on three rail layouts. This version of the board includes internal current limiters. Useful anyplace that an external voltage needs to be monitored. (5V-20V AC-DC-DCC)

Relay Board - 4 is a Quad 10A SPDT relay board with logic level drivers. It is suitable for use with TC Mark II, TowerMan, Tower LCC, or other logic level output devices. It requires 12V auxiliary power to supply the relay coils. Auxiliary power is...

(Single Coil Solenoid Driver) This 8 line, optically isolated, single ended, high current, high voltage DC driver can drive up to 1A continous per line at up to 30VDC. When used with custom Tower LCC settings and a CD power supply this board will drive 4...