DCC & DC

5 pack  On/On DPDT Toggle Switch  5a 125v

Part Number5240299 Dimensions100ft of 20mm (.787) NCEKAP20 100ft of 20mm (.787) Kapton Tape Polyimide Film Tape consists of Kapton® polyimide film and silicon adhesive. It is designed for high temperature applications. Temperature use range is -100...

Part Number5240298 Dimensions100ft of 10mm (.393) NCEKAP10 100ft of 10mm (.393) Kapton Tape Polyimide Film Tape consists of Kapton® polyimide film and silicon adhesive. It is designed for high temperature applications. Temperature use range is -100...

DCC Main Bus Wire, (Red), 14AWG, 50 Feet NCE Multi Scale DCC Main Bus Wire Red 50'

DCC Main Bus Wire, (Black), 14AWG, 50 Feet NCE Multi Scale DCC Main Bus Wire Black 50'

Layout Wiring Kit, 100 Foot DCC power bus. DCC main bus wiring for typical 100 foot double track mainline. Includes: • Main Bus - 100 feet each red and black 14 AWG stranded wire • Feeder Wires - 32 each red and black feeder 22 AWG wires...

Same six-wire connectors in front as UTP but allows use of off-the-shelf CAT5 cables to connect panel-to-panel at rear. Can be used as a cab bus splitter and also adds the ability to add power to the cab bus for larger layouts.

The AR10 is an automatic reverse loop controller for DCC layouts. It requires just 4 connections, two to the main line and two to the loop. In addition it functions as a circuit breaker for the reverse loop. Recommended for DCC systems from 1 to 10Amps.

Build your control panels with greatly simplified wiring. Just connect push buttons to the Mini Panel and use to issue turnout routing macros, individual turnout commands by pushing one button. Set up is easy, just plug in a Pro Cab (sold separately) and...

Description: It is usually desirable to divide a layout into separate track power sections (power districts) so that a derailment or short circuit on one section of the layout doesn't shut down power to other sections. The CP6 can be used to divide the...

Provides short circuit protection for one power district. Can be used with most DCC systems.  This is not recommended for use with the PowerCab. For the PowerCab use a CP6!

Add this USB computer interface for computer programming and/or operation of your Power Cab equipped layout. Requires USB cable, computer and railroad computer program such as JMRI Decoder Pro and Panel Pro

Add a separate PCP panel to operate your PowerCab in other places or on other layouts. Use the P114 and you will only have to move the PowerCab.

13.8v DC Power Supply. 1.3 Amp / 2 amp peak. US approved power supply suitable for PowerCab and other applications. This plugs into the back of panels such as the PCP(PowerCab connection panel) and the UTP-CAT5

This is our lowest cost, easiest to use cab bus panel. All four RJ-12 jacks are wired in parallel for easy plug and play use. This board also provides a convenient point to add additional 12 Volt cab bus power, just plug in a 12 Volt "wall wart" power...

Dimensions: 0.595" x 0.390" (15mm x 10mm)  Direct plug in to locos equipped with Next18 (NEM-662) socket  Features of this decoder: Silent Running(TM) Torque compensated motor drive Torque Compensation for ultra smooth low speed...

N Scale N14K2 Drop-In Control Only Decoder. Includes pre-soldered motor clips.

Drop in decoder for Kato N scale. Includes pre-soldered motor clips. Works for: Athearn EMD F45 Athearn EMD FP45  Kato "Gevo" ES44AC  Kato AC4400  Kato C30-7  Kato GE C44-9W Kato SD40-2 early versions Kato ES44  ...

All new easy programming with no jumpers. Features: On board display Control for 8 Tortoise switch machines Remembers the position of switch during power outages Supports the full range of DCC accessory addresses (1-2044) Easy address...

Your Kato Unitrack and LGB remote control turnouts can now be DCC controlled. The Switch-Kat provides connections for optional switch position indicator lights and "local control" pushbuttons. Simple installation, two wires to the track, two wires to the...