DCC Accessories

RJ12 cable with a length of 2 feet. For use with DCC systems such as Digitrax LocoNet.

SwitchPilot 3 Plus decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption. In order to facilitate the rather...

RJ12 cable with a length of 2 feet. For use with DCC systems such as Digitrax LocoNet.

With the abundance of lighting functions and wanting to see and check them before I placed the shell on the frame, I decided I needed a way to see what was happening!  I went to work and prototyped a small connector board with LEDs so I could...

The UWT-100 Universal WiFi Throttle from TCS is the new standard in WiFi control for model railroads. This throttle brings a new level of ergonomic comfort and operational convenience to handheld controls. Instead of spending time with your head...

Plug and Play Universal fascia panel supporting LocoNet. Two RJ12 front panel Throttle jacks. Three RJ12 rear pass-through LocoNet jacks Supports throttle charging. Fully connectorized installation. 2mm rear plug for e.g. PS14 DC power supply. 4-pin...

4 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management. Each DS supports Occupancy detection. Each...

Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28 - AWG 12 so there is no problem connecting different wire sizes together. Easily disconnect wiring for trouble...

This plastic mounting track is suitable for mounting a single I/O module to a flat surface. (3 1/2" x 2")

Set of 4 CT (Current Transformer) coils for BOD4 or BOD4-CP.

Set of 8 CT (Current Transformer) coils for BOD-8. These 100:1 toroid coils sense the track current on leads passing through the hole in the middle of the coil. They connect to the BOD-8 with twisted pair cable such as CAT-3 or CAT-5 network cable. (up...

(Block Occupancy Detector-4) This board operates as a DCC occupancy detector for 4 blocks using remote CT coils. It outputs logic levels, and has a RR-CirKits standard ribbon connector interface. The "Power-Lok" feature optionally monitors the DCC bus...

(Block Occupancy Detector-8 - SM) This new board is compatible with LCC node sample mode which allows using output drivers on the same I/O port. This board operates as a DCC occupancy detector for 8 blocks using remote CT coils. It outputs logic levels,...

16 Led drivers plus 8 line Input/Output node for NMRA CAN bus LCC®. Logic level I/O port compatible with other standard RR-CirKits I/O modules. Boot Loader for user installable firmware upgrades. Includes powerful internal Logic Elements. Compatible with...

16 Led drivers plus 8 line Input/Output node for NMRA CAN bus LCC®. Logic level I/O port compatible with other standard RR-CirKits I/O modules. Boot Loader for user installable firmware upgrades. Includes powerful internal Logic Elements. Compatible with...

  Eight 9G servo decoder for 2-position Slow-motion turnouts. Configurable to control eight 3-position semaphores. Works with compatible LocoNet Systems. Plug and play connections. Option setup switches for configuration. On-layout...

A double-pole, double-throw relay with actuating mechanism driven by a momentary-power, twin coil solenoid. (A solenoid is a cylindrical coil of insulated wire in which an iron core is made to move back and forth by a flow of electric current.) With just...

This 13.6mm x 9.6mm speaker could be classified as a "sugar cube" speaker. This style of speaker is often feature in cell phones and tablets and performs slightly differently from standard speakers. This style of speaker REQUIRES mounting with a baffle...

TCS Keep-Alive® (KA) devices are used to supply power to decoders during times of power interruption due to dirty track or problematic track work. Newly-redesigned at half the size of a KA4, the KA2 will power HO or N scale locomotives with approximately...

TCS Keep-Alive® (KA) devices are used to supply power to decoders during times of power interruption due to dirty track or problematic track work. Newly-redesigned and coming in at half the size of a KA3, the KA1 will power HO or N scale locomotives...