N Scale Track and Accessories

A spectacular model with extra clearance to allow double stacked containers to pass through. The detail molded into this styrene kit will make this kit a center piece of any model display. Any modeler can now construct a steel bridge model in a few hours...

The Central Valley N scale Truss Kit is a spectacular model with detail that will be the center piece of any model display. Any modeler can now construct a steel bridge model in a few hours that surpasses any model of similar structures in the past! ...

This cable and actuator is designed to be used with the Remote Signal Activator (sold separately). Instructions for assembly are provided with the Remote Signal Activator.

Remote Signal Activator Mounting bracket and mechanism utilize the TORTOISE (not included) and a special drive wire cable assembly to remotely actuate any crossing gate, train order board, or upper/lower quadrant semaphore signal having a...

6 pack of the Circuitron Smail with Terminal Block Smail (Slow Motion Actuator with Integrated Logic) features same size and mounting as the TORTOISE (sold separately).  Compatible with all DCC systems that provide accessory address control...

6 pack of the Circuitron Smail. Smail (Slow Motion Actuator with Integrated Logic) features same size and mounting as the TORTOISE (sold separately).  Compatible with all DCC systems that provide accessory address control. Two-wire connection to DCC...

Smail (Slow Motion Actuator with Integrated Logic) features same size and mounting as the TORTOISE (sold separately).  Compatible with all DCC systems that provide accessory address control. Two-wire connection to DCC bus with no external power...

Smail (Slow Motion Actuator with Integrated Logic) features same size and mounting as the TORTOISE (sold separately).  Compatible with all DCC systems that provide accessory address control. Two-wire connection to DCC bus with no external power...

The CIRCUITRON Remote Tortoise Mount is capable of driving up to 2 cables and actuators at the same time, thus allowing a single TORTOISE to actuate two sets of points simultaneously, such as for crossover use. However,...

The CIRCUITRON Remote Tortoise™ Mount consists of a molded base mechanism to which the TORTOISE™ (not included) is mounted. An adjustable lever arm is fastened onto the TORTOISE™ output and drives a stainless steel wire inside a...

  Prototypical turnouts don't snap open and closed, they move slowly. This easy-to-mount switch machine features prototypical slow-motion action-three seconds to complete throw. Easy-to-mount slow-motion switch machine features: Prototypical...

 Prototypical turnouts don't snap open and closed, they move slowly. This easy-to-mount switch machine features prototypical slow-motion action-three seconds to complete throw. Easy-to-mount slow-motion switch machine features: Prototypical...

Single Cut Stone Tappered Abutment -- pkg(2) 3 x. 2.4"

Single-Track Cut Stone Bridge Abutment -- 1-3/4 x 5/8 x 2-1/4" 4.5 x 1.6 x 5.7cm pkg(2)

Cut Stone Bridge Pier 2-Pack -- 2-1/2 x .5 x 2" 6.4 x 1.27 x 5.1cm

Strong, self-lubricating black Delrin ground throws with external cam for strength and maximum throw. Molded on pin for direct mounting.  All 200 series units (Sprung) have internal springs so they can be connected directly to the turnout throwbar...

The SPDT contact can be used to power a turnout frog, a signaling system, or a relay coil.  A shim to raise the stand to tie level and five different end fittings to connect to most turnouts are provided.  Hook end for Atlas, blade for Roco, hole for...

Model Tech Studios D0080 - Roadside Trash Bags - HO Scale OPERATING STANDARD GROUND THROWS All Ground Throws offer these advantages: Molded of strong, self-lubricating black Delrin. External cam provides maximum life and travel. Cam design...

Strong, self-lubricating black Delrin ground throws with external cam for strength and maximum throw. Molded on pin for direct mounting. All 200 series units (Sprung) have internal springs so they can be connected directly to the turnout throwbar...

The 206S features internally sprung stands. Stainless steel springs take up the overtravel and maintain tension to hold the movable points agianst the stock rails of the turn out. These springs make the machines easy to mount to the turnout. ...