DCC Accessories

Keep Throttles Off Layout Scenery with Throttle Pockets™ During layout operating sessions modelers are always looking for a place to set down their throttles. Universal Throttle Pockets from New Rail Models offer a convenient alternative to...

Keep Throttles Off Layout Scenery with Throttle Pockets™ During layout operating sessions modelers are always looking for a place to set down their throttles. Universal Throttle Pockets from New Rail Models offer a convenient alternative to...

Part Number5240299 Dimensions100ft of 20mm (.787) NCEKAP20 100ft of 20mm (.787) Kapton Tape Polyimide Film Tape consists of Kapton® polyimide film and silicon adhesive. It is designed for high temperature applications. Temperature use range is -100...

Part Number5240298 Dimensions100ft of 10mm (.393) NCEKAP10 100ft of 10mm (.393) Kapton Tape Polyimide Film Tape consists of Kapton® polyimide film and silicon adhesive. It is designed for high temperature applications. Temperature use range is -100...

Same six-wire connectors in front as UTP but allows use of off-the-shelf CAT5 cables to connect panel-to-panel at rear. Can be used as a cab bus splitter and also adds the ability to add power to the cab bus for larger layouts.

The AR10 is an automatic reverse loop controller for DCC layouts. It requires just 4 connections, two to the main line and two to the loop. In addition it functions as a circuit breaker for the reverse loop. Recommended for DCC systems from 1 to 10Amps.

Build your control panels with greatly simplified wiring. Just connect push buttons to the Mini Panel and use to issue turnout routing macros, individual turnout commands by pushing one button. Set up is easy, just plug in a Pro Cab (sold separately) and...

Provides short circuit protection for one power district. Can be used with most DCC systems.  This is not recommended for use with the PowerCab. For the PowerCab use a CP6!

Add this USB computer interface for computer programming and/or operation of your Power Cab equipped layout. Requires USB cable, computer and railroad computer program such as JMRI Decoder Pro and Panel Pro

Add a separate PCP panel to operate your PowerCab in other places or on other layouts. Use the P114 and you will only have to move the PowerCab.

13.8v DC Power Supply. 1.3 Amp / 2 amp peak. US approved power supply suitable for PowerCab and other applications. This plugs into the back of panels such as the PCP(PowerCab connection panel) and the UTP-CAT5

Decoder Test Kit. Perfect companion to DCC installation and operation. The decoder tester works with ANY DCC decoder. Test for motor forward and reverse, functions F0F, F0R, 1, and 2. A DCC system is required for functionality, the DTK acts as an...

This is our lowest cost, easiest to use cab bus panel. All four RJ-12 jacks are wired in parallel for easy plug and play use. This board also provides a convenient point to add additional 12 Volt cab bus power, just plug in a 12 Volt "wall wart" power...

Detects DCC current being drawn in a block. Connects to AIU01 or Mini Panel. Isolated so that there is no electrical connection to the track. Needs no external power for most operations, suitable for DCC power up to 20 Amps. Can light up LED or operate...

The Auxiliary Input Unit (AIU) provides a means of connecting external devices such as switch contacts, Block Detectors (BD20), or other sensors to the NCE Cab Bus or Command Station. These external devices can be anything that supplies an electrical...

All new easy programming with no jumpers. Features: On board display Control for 8 Tortoise switch machines Remembers the position of switch during power outages Supports the full range of DCC accessory addresses (1-2044) Easy address...

Your Kato Unitrack and LGB remote control turnouts can now be DCC controlled. The Switch-Kat provides connections for optional switch position indicator lights and "local control" pushbuttons. Simple installation, two wires to the track, two wires to the...

Engineer cab with LED display uses a more conventional potentiometer knob for speed control. Definite stop and starting points. Note** the speed setting of the knob is instantly applied to any locomotive selected. Clear, easy-to-read display, select up...

Engineer cab with LED display uses a more conventional potentiometer knob for speed control. Definite stop and starting points.  Clear, easy-to-read display, select up to 6 loco recalls, F0-F28, select accessory, select macro. Note: the speed...

The Cab06 uses a more conventional knob for speed control. The Cab06 can be set to YARD mode. Yard mode makes the speed knob act as a "center off" speed control. Turn the knob to the right and the loco will increase speed in the forward direction. Turn...