Adhesives

Roberts Brick Mortar provides an added touch of realism to your model by making it easy to simulate the look of realistic white brick mortar. Simple to use and apply. Water clean-up, non-toxic, quick drying time. Can be used in a variety of modeling...

No more spills! This Creations Unlimited Touch-N-Flow Work Base holds everything you need to keep your Touch-N-Flow applicator and Solvent Cement ready for use. Base holds a 2oz bottle of Solvent Cement, Filler-Cleaner Bottle and Touch-N-Flow Applicator...

No more spills! This Creations Unlimited Touch-N-Flow Work Base holds everything you need to keep your Touch-N-Flow applicator and Solvent Cement ready for use. Base holds a 2oz bottle of Solvent Cement, Filler-Cleaner Bottle and Touch-N-Flow Applicator...

Applies plastic solvent cements (Tenax-7R or Ambroid Pro-Weld are recommended) or CA activators with pinpoint accuracy.

Faller Expert Laser Glue is a multi-purpose glue for bonding wood, cardboard, foam and decorating parts. Ideal for building laser-cut models.

Faller Expert Liquid Plastic Cement provides excellent results when bonding plastics. The special needle applicator allows precise application of adhesive.

INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from...

SUPER-GOLD™ Thin and SUPER-GOLD+™ gap filling medium thickness are our odorless foam safe CAs. They are non-frosting and take only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose...

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids...

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface...

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the...

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight...

QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to...

Track cleaner and corrosion inhibitor. Penetrates existing corrosion layers and restores electrical conductivity to the track. Also retards future corrosion by a molecular reaction with the base metal. Non-toxic, contains no solvents, acids, alkalies or...

High viscosity, slow-cure adhesive has a 30-40 second positioning time and cures in 1-2 minutes. The high-viscosity formula permits use on poorly fitting surfaces, large bond areas and is a surface-sealing agent for cloth and porous surfaces. Bonds oily...

Water-based material softens and removes cured cyanoacrylates, paint and hobby decals. Also removes ball-point pen inks, permanent marker inks, typist correction fluid, nail polish and scuff marks from painted surfaces. Safe for most plastics. Zap Z-7...

"ZIP-KICKER" accelerator for super glues forces immediate cure for all cyanoacrylates. Use of this accelerator also expands gap-filling ability, permits structural fillet forming and solves tough-to-bond combinations of materials. Zap Zip Kicker --...