Electronics

This function-only decoder is designed for any scale where extra lighting features and functions are needed. These decoders are commonly used for smoke coils, fireboxes, or step lights. Note: FL-series decoders do not provide motor control. A separate...

This function-only decoder is designed for any scale where extra lighting features and functions are needed. This decoder includes a 6-pin harness for easy installation and wiring. These decoders are commonly used for smoke coils. Note:...

Tortoise Card Edge Connector Our Edge Connector Now without shims redesigned for a SNUG fit for the updated tortoise switch machine. The newer tortoises have a green edge connector. See images. See ACL1000 to fit older switch machine

Plug and Play Universal fascia panel supporting LocoNet. Two RJ12 front panel Throttle jacks. Three RJ12 rear pass-through LocoNet jacks Supports throttle charging. Fully connectorized installation. 2mm rear plug for e.g. PS14 DC power supply. 4-pin...

Finally, a Model Railroading Video Camera that fits neatly inside your engines (HO or larger) and rolling stock — powered by DCC/DC track power.   Climb into the Cab with a Choo Choo Vision Model Railroad CAB-CAM.  View your layout in...

4 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management. Each DS supports Occupancy detection. Each...

15V DC Power Adapter (1500mA Output, 100-240V AC Input) This high quality regulated switching power adapter powers any 15 Volt DC device up to 1.5 Amp. Made with quality in mind, this unit outperforms similar products. Let RR-CirKits keep your devices...

The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot...

Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28 - AWG 12 so there is no problem connecting different wire sizes together. Easily disconnect wiring for trouble...

Servo Extension Cable (M-F) This 39" cable may be used to extend the length of the above (M-M) cables.

Servo Connection Cable (M-M) This 20" cable may be used to connect two Quik-Link devices.

The TAB is designed to provide a solder-less connection between the SMD-8 and Tortoise. It includes 10 pin daisy chain cable headers and channel selection jumpers. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. An 8...

The Tortoise Quik-Link is a plug on Tortoise driver board. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. It connects directly to any LCC output port with a standard 10 pin ribbon cable or via a QL-Breakout using a...

This plastic mounting track is suitable for mounting six I/O modules to a flat surface. (3 1/2" x 12")

This plastic mounting track is suitable for mounting four I/O modules to a flat surface. (3 1/2" x 8")

This plastic mounting track is suitable for mounting three I/O modules to a flat surface. (3 1/2" x 6")

(10 position IDC male with latch) Box of 10 Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension cables. Screw ears allow easy mounting to the layout.

(Fan Out Board, Dual Direct) This board is specifically designed to terminate the dual cable, eight stall motor, connections from a single SMD-8 board. It includes on board jumpers to select common positive or common negative for optional single ended...

Fan Out Board, Direct Drive) This board is specifically designed to direct drive eight LED's from a single RR-CirKits port. It includes on board locations for current limiting resistors and jumpers to select common anode or common cathode connections. No...

This board is normally used for block detection on three rail layouts. This version of the board includes internal current limiters. Useful anyplace that an external voltage needs to be monitored. (5V-20V AC-DC-DCC)