Electronics

You can often reverse your servo throw direction by turning it around or reversing the servo linkage.  Sometimes there just isn't room under a turnout to do this.  You can't reverse the servo direction by swapping wires since servos work by...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

Singlet Micro DCC Accessory DecoderDesigned exclusively for switching turnouts with a servo No buzzing! - servo turns off at end of throw Simpler setup - center the servo and mount - no alignment needed Switch with DCC or the included fascia...

Singlet Micro DCC Accessory DecoderDesigned exclusively for switching turnouts with a servo No buzzing! - servo turns off at end of throw Simpler setup - center the servo and mount - no alignment needed Switch with DCC or the included fascia...

Sometimes a servo will buzz or chatter continuously.  Some poeple find this very annoying. The No-Buzz goes in line with the servo cord and quiets the servo.  Here is how it works - if the servo is stopped in the same position for more than...

You can control your Octopus II or III with the Octocoder, a simple stationary DCC decoder.  The board provides connections os you can also connect fascia controllers and LEDs for local control. (Will not work with toggle switches however.) No...

Remote Aligner for Octopus IIIUsed with the Octopus III (above) for alignment of servos (cannot be used with the Octopus II).  Just one of these needed for all of your Octopus IIIs.  Comes with a 7' cable which allows you to stand next to...

Servos, mounting brackets, extension cables, Y cables and reversers and parts to make working with servos easier. As well as the servo decoders on the Tam Valley Depot website, all of the servo products on this page work with all R/C servo controllers...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

SwitchWright DCC/Relay version Bare Board  Just the bare board for making up your own machines.  The board includes the servo drive circuitry with builtin DCC decoder and a DPDT relay. To make a complete turnout installation you will...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

1" wide x 36 yd. roll of Kapton tape.

This M4 decoder (see M4 for more information) comes connected to a 3.5" (8.89 cm) long harness which is terminated with a 8-Pin NMRA plug rotated 180 degrees from the standard orientation. This allows the decoder to fit better in certain applications...

This M4 decoder (see M4 for more information) comes connected to a 5" (12.7 cm) long harness which is terminated with a 8-Pin NMRA plug. From M4 listing 1011 Back EMF Load Compensation: Provides superior slow speed control and high performance...

This M4 decoder (see M4 for more information) comes connected to a 3.5" (8.89 cm) long harness which is terminated with a 8-Pin NMRA plug rotated 90 degrees from the standard orientation. This allows the decoder to accommodate the UK's narrow gauge...

This custom-designed holder can hold a single TCS UWT-100 throttle. Includes: 1 - 3D printed holder designed perfectly for the UWT-100 1 - Bag of 2 Screws

Buy this pack and save on UWT-100 Throttle holders! This holder only fits the UWT-100. Includes: 3 - 3D printed holder designed perfectly for the UWT-100 3 - Bags of 2 Screws

Description Allows for quick and precise installation of the RC522 Antenna.

Description The DC to DC converter takes an input voltage of 8 to 22VDC (12VDC accessorypower supply) and converts it to 5VDC output.

8mm RFID NFC Tag Mifare Classic 1k (25 pcs).  Up to 5mm range.