Electronics

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

SPDT Snap Switch for Miniature Servo Bracket   Snap Switch mounts on the back of the bracket with the 2 included screws and some thick CA glue. Provides a set of contacts for controlling frog power  or signaling. Switches near dead center...

Servos, mounting brackets, extension cables, Y cables and reversers and parts to make working with servos easier. As well as the servo decoders on the Tam Valley Depot website, all of the servo products on this page work with all R/C servo controllers...

Servos, mounting brackets, extension cables, Y cables and reversers and parts to make working with servos easier. As well as the servo decoders on the Tam Valley Depot website, all of the servo products on this page work with all R/C servo controllers...

Servos, mounting brackets, extension cables, Y cables and reversers and parts to make working with servos easier. As well as the servo decoders on the Tam Valley Depot website, all of the servo products on this page work with all R/C servo controllers...

You can control your Octopus II or III with the Octocoder, a simple stationary DCC decoder.  The board provides connections os you can also connect fascia controllers and LEDs for local control. (Will not work with toggle switches however.) No...

Remote Aligner for Octopus IIIUsed with the Octopus III (above) for alignment of servos (cannot be used with the Octopus II).  Just one of these needed for all of your Octopus IIIs.  Comes with a 7' cable which allows you to stand next to...

Octopus IIIBoard has 8 positions for driving servos between two positions and 8 inputs for fascia controllers (see below) or toggle switches.  Octopus III uses the remote board (below) to align the servos and has automated endpoint adjustment as...

This adapter mates with the above two power supplies to make them easy to hook up to wires using the screw terminals. Jack size is 5.5/2.1 mm. Plus and minus terminals are marked. Price is for one adapter - picture shows two to illustrate both ends.

This adapter mates with the DCC boster power jack in order to hook up your own power supply using the screw terminals. Plug size is 5.5/2.1 mm. Plus and minus terminals are marked. Price is for one adapter - picture shows two to illustrate both ends.

The ideal power supply for the SwitchWright, this unit is well-regulated and current protected. The unit has a barrel connector that fits the adapter below or you can cut it off and strip the wires. It can support about 30 SwitchWright switch machines...

12V 5A Power Supply for Accessory Bus Use12V 5A 60W switching power supply. Best for powering Quads and Singlets.  Plug size is 5.5/2.1 mm. Power supply comes with a US 110V plug.  By swapping the power cord can be used with...

16V 4.5A Power Supply for Track Power Use16V 4.5A 72W switching power supply - best for track power.  Delivers about 15 V to track when used with our booster above.  Plug size is 5.5/2.1 mm. Power supply comes with a US 110V plug.  By...

5 Amp Trip / 3 A Continuous Duty DCC Booster BoardDCC Booster board without the power supply.  These boards can be used to make locomotive Power Districts or an Accessory District with a shared power supply.  A jumper is used to set...

DCC Mono Frog Juicer (polarity reverser for frogs)For all DCC systems including NCE PowerCab.  This board is an automatic polarity reverser for a single frog.  Setup is simple, connect two wires to the DCC bus and one wire to a frog.  The...