Electronics

This 25mm x 14mm speaker is a tough little beast capable of accepting 2W of audio and still producing a clear and accurate sound. The military spec. rating of these speakers means they are dust proof and IPX5 certified water proof. Truly an impressive...

Speaker - 17.5 x 25.5 x 6.7 mm Great for low hood diesels and small steam locos Speaker with two 11x15mm (4/5 Ohm impedance) sugar cube speakers installed with wire Four mounting tabs

Features:Series 3 HO Plug ‘N Play Decoders with Integrated Plug Compatible with Sound Bug (Note this is not a plug n' play installation, wiring is required) Decoder Lock equipped

Fits many 21MT equipped HO locomotives Digitrax 21-pin MT socket 1.0 Amp/2 Amps Peak 8 FX7 Functions, 300ma Output

Fits many Kato N-locomotives Drop-in light board replacement decoder for Kato “K0” form-factor boards 1.0 Amp/2 Amps Peak 6 FX3 Functions, 200ma output

This small speaker is perfect for narrow hood diesels and anywhere else where space is at a premium. Dimensions: 25 x 14 x 5.2mm(D)Frequency Response: 740Hz - 4kHzPower: 1 Watt (Nominal) 1.5 Watts (Peak)Impedance: 8 Ohms

 It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor. LT1 Features: Use as a diagnostic tester Test decoders prior to...

This adapter allows you to use our smallest decoder (The TSU-N18) in practically any n-scale model! Bring the TSU-N18's 6 functions plus a narrower profile to your models. The JST-Next18 Adapter features a Next18 socket to simply plug-in your TSU-N18...

A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer...

The CN is a N-scale drop-in decoder for older Atlas, Kato, and Intermountain locomotives. Examples include the following: Atlas: GP7/GP9 Old Style GP30/GP35 Old Style SD35/SD50/SD60/SD60M B30-7/B40-8 GP38 GP40 DCC-Ready SD9...

The single input breakout board for the BDL168 block detection eliminates soldering connections to the card edge or card edge adapter of this product. This design has a single input, meaning all 4 detection zones (and all 16 sections) are connected to a...

  Keeps locos & sound running during power interruptions caused by dirty or bad track. Hold up time varies based on decoder load & track conditions. PX112-2 Plug ‘N Play Install on DH126 & DH166 Series Decoders PX Body Size 1...

The LokSound 5 is the most important member of the LokSound family. Due to the combination of the digital decoder and the sound module on one circuit board we achieve the smallest possible dimensions of 30 mm x 15.5 mm. Therefore it fits into almost any...

N Scale N14K2 Drop-In Control Only Decoder. Includes pre-soldered motor clips.

Set of 8 CT (Current Transformer) coils for BOD-8. These 100:1 toroid coils sense the track current on leads passing through the hole in the middle of the coil. They connect to the BOD-8 with twisted pair cable such as CAT-3 or CAT-5 network cable. (up...

A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer...

A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer...

This colored wire will make wiring your layout easier than ever! Twenty gauge stranded copper; 50' reel.

Fits many 21MT equipped HO locomotives Digitrax 21-pin MT socket 1.0 Amp/2 Amps Peak 2 FX7 Functions, 300ma Output