Electronics

(Stall Motor Driver) LCC sample mode compatible. This 8 output, optically isolated, low current "H" bridge driver is designed for control of 8 stall motor switch machines. (E.g. Tortoises®) It can drive up to 100ma. per line, speed regulated output 6 to...

This decoder is a T4 decoder with built in Keep-Alive™, and will keep your locomotive operating for 6-15 seconds without power (As a result of dirty track, poor contacts, etc.). This decoder is physically larger than a T-series decoder, but features the...

Universal speaker housing for the TCS 13.6mm x 9.6mm speaker (included). This simple, closed design channels both the front and rear audio out the front of the speaker housing. These micro speakers do not work without being mounted to an enclosure (like...

Breakout board for the Digitrax PM42 board The PM42 breakout board is setup to accept up to 2 inputs and 4 distinct outputs. Each output can be configured with jumpers to make it a reversing section. The board comes with one set of jumpers that allows...

Fits E24 plug N locomotives and compatible units Plug-in E24 socket Motor drive at connector capacity 13 FX7 Functions, 200mA capacity 8 CV Selectable Steam & Diesel Sound Schemes Included

The LokSound 5 micro DCC Direct Kato Japan has been specially developed for installation in Kato-branded track N vehicles: in many European and Japanese locomotives of this manufacturer, the ser decoder can be installed directly below the engine instead...

The LokSound 5 micro DCC Direct Kato USA SC44 was specially developed for installation in some Kato USA N gauge vehicles: It fits in all Kato N scale locomotives Siemens SC44 “Charger” or MP36 instead of the standard analog board. Finally,...

The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of...

The LokPilot 5 micro DCC Direct Kato USA Widebody is the “twin” of the LokSound 5 micro DCC Direct Kato USA Widebody. With its dimensions of 47.5mm x 14.0mm x 4.5mm it  has been specially developed for installation in wide body N...

Makes it easy to test electrical contacts and circuits.

Features 2 Switches, Center Off, Momentary Spring Return Both Sides S.P.D.T. 5 Amp 120 V 1/4 in. Diameter

Our deluxe Radio Equipped Pro Cab R provides the most user-friendly access to all system features. Uncomplicated menus on the easy to read, backlit LCD display guide you through the most advanced operations with a minimum of fuss. Instant control of up...

DCC Main Bus Wire, (Red), 14AWG, 100 Feet NCE Multi Scale DCC Main Bus Wire Red 100'

15V DC Power Adapter (1500mA Output, 100-240V AC Input) This high quality regulated switching power adapter powers any 15 Volt DC device up to 1.5 Amp. Made with quality in mind, this unit outperforms similar products. Let RR-CirKits keep your devices...

HO-scale, 2-function decoder that measures 17 x 17 x 7mm in a plug-and-play format suitable for use with a variety of models. It is manufactured with an NMRA compatible 8-pin ‘direct-plug.' This decoder will operate in DCC only. Dimensions: 17 x 17...

Blunami will change the way you enjoy the model railroading hobby! The BLU-PNP8 is a universal factory board replacement sound decoder suitable for use in many manufacturer’s diesel models such as those made by Atlas, Athearn, and...

This decoder is a M4 decoder with built in Keep-Alive™, and will keep your locomotive operating for 6-15 seconds without power (As a result of dirty track, poor contacts, etc.). This decoder is physically larger than a M-series decoder, but...

Works with the NCE Power Cab or Cab Bus. See WFD-30 for use with only NCE Cab Bus Install this Wi-Fi device on your NCE layout to provide Wi-Fi access.  Then use the power of the TCS universal WiFi throttles on your NCE layout to control trains. A...

RJ12 cable with a length of 12 feet. For use with DCC systems such as Digitrax LocoNet.