Electronics

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

You can often reverse your servo throw direction by turning it around or reversing the servo linkage.  Sometimes there just isn't room under a turnout to do this.  You can't reverse the servo direction by swapping wires since servos work by...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

Fascia Controllers Crossover Fascia Controller   3D printed mount for fascia controllers The Fascia Controller plug in to our servo controllers to provide an easy way to control your turnout.   Skill Level: Basic - simply plug...

1/2" wide x 36 yd. roll of Kapton tape.

The IMF4 is a N-scale drop-in decoder which is designed for InterMountain F-unit locomotives. Examples include the following: InterMountain: F3A/B F7A/B F9B See the installation pages for a full list of compatible engines! NOTE: This version of...

This M1 decoder (see M1 for more information) comes connected to a 3.5" (8.89 cm) long harness which is terminated with a 8-Pin NMRA plug. From M1 listing 1006 The M1 is a small form factor hard-wire decoder with 2 lighting functions for HO-scale...

TCS Keep-Alive® (KA) devices are used to supply power to decoders during times of power interruption due to dirty track or problematic track work. The WAUX-KA4 will power an HO-Scale locomotive with headlights on for approximately 6 to 20 seconds...

The IMD4 is a N-scale drop-in decoder which is designed for InterMountain locomotives. Examples include the following: InterMountain: SD40-2W See the installation pages for a full list of compatible engines! Back EMF Load...

Producing sounds with the clarity and volume of a much larger speaker these 30mm (1.18") speakers are perfect for tight installations that still require BIG sound. Dimensions: 1.18" diameter x 0.22" or 30mm diameter x 5.7mm Sound Pressure Level:...

Universal speaker housing for the TCS 28mm round speaker (included). This simple, closed design channels both the front and rear audio out the front of the speaker housing. This housing should only be used in models with a closed upper shell, such as...

Fits Intermountain N Scale FP7A with wired motors produced after Jan 2014 6 FX3 Functions 472” x 2.165” x .098”11.98mm x 54.99mm x 2.4mm   ▪FX3 Function outputs for prototypical lighting effects and on/off...

  For use with Digitrax Decoders Equipped with 6 pin Function Harness 8 ohm 16 x 26 x 9 mm box speaker included Keeps locos running during intermittent power interruptions resulting from dirty or bad track. 0.33 F Capacitance ...

  Keeps locos running during power interruptions caused by dirty or bad track. Keeps light and other functions from dropping out due to power interruptions. Hold up time varies based on decoder load & track conditions. Use with Digitrax...

Fits Kato FP40-PH or compatible HO locomotives Drop-in light board replacement 1.0 Amp/2 Amps Peak 8 FX3 Functions, 200ma Output 8 Ohm 28 mm round speaker w/330uF Capacitor

Fits many HO, O & G Scale installations. 53mm x 18mm x 14mm. 32 Ohm, 1/2 watt rating. Acoustically matched enclosure included for best sound level. For use with decoders that specify 32 Ohm speakers.

The LokPilot 5 Fx DCC is a function decoder without motor output and is therefore perfect for installation in control cars or function models. As the "twin brother" of the LokPilot 5 Fx, it shares its characteristics and also the basic...

The LokPilot 5 Fx DCC is a function decoder without motor output and is therefore perfect for installation in control cars or function models. As the "twin brother" of the LokPilot 5 Fx, it shares its characteristics and also the basic...

The LokPilot 5 is the most important representative of the LokPilot family and is suitable for almost all questions in locomotives of gauge H0 and 0. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 is a real...