Electronics

This is our lowest cost, easiest to use cab bus panel. All four RJ-12 jacks are wired in parallel for easy plug and play use. This board also provides a convenient point to add additional 12 Volt cab bus power, just plug in a 12 Volt "wall wart" power...

Detects DCC current being drawn in a block. Connects to AIU01 or Mini Panel. Isolated so that there is no electrical connection to the track. Needs no external power for most operations, suitable for DCC power up to 20 Amps. Can light up LED or operate...

The Auxiliary Input Unit (AIU) provides a means of connecting external devices such as switch contacts, Block Detectors (BD20), or other sensors to the NCE Cab Bus or Command Station. These external devices can be anything that supplies an electrical...

Drop in decoder for Kato N scale. Includes pre-soldered motor clips. Works for: Athearn EMD F45 Athearn EMD FP45  Kato "Gevo" ES44AC  Kato AC4400  Kato C30-7  Kato GE C44-9W Kato SD40-2 early versions Kato ES44  ...

Plug in 4 function decoder with 6 pin NEM 651 connector Dimensions: 2.65 X 8.77 mm Includes pins 19.41 mm

All new easy programming with no jumpers. Features: On board display Control for 8 Tortoise switch machines Remembers the position of switch during power outages Supports the full range of DCC accessory addresses (1-2044) Easy address...

Engineer cab with LED display uses a more conventional potentiometer knob for speed control. Definite stop and starting points. Note** the speed setting of the knob is instantly applied to any locomotive selected. Clear, easy-to-read display, select up...

Engineer cab with LED display uses a more conventional potentiometer knob for speed control. Definite stop and starting points.  Clear, easy-to-read display, select up to 6 loco recalls, F0-F28, select accessory, select macro. Note: the speed...

The Cab06 uses a more conventional knob for speed control. The Cab06 can be set to YARD mode. Yard mode makes the speed knob act as a "center off" speed control. Turn the knob to the right and the loco will increase speed in the forward direction. Turn...

An entire DCC system in the palm of your hand! This 2 Amp system can operate up to 4 HO locomotives or 8 N scale locomotives running at the same time. Provides all of the capability and ease of use that you’ve heard about in our Power Pro system at an...

Our deluxe Radio Equipped Pro Cab R provides the most user-friendly access to all system features. Uncomplicated menus on the easy to read, backlit LCD display guide you through the most advanced operations with a minimum of fuss. Instant control of up...

Deluxe cab provides user-friendly access to advanced system features. Backlit LCD displays guide you through operations easily. Both a thumb wheel knob and repeating push buttons for speed control are provided. Control of single or multiple turnouts,...

Requires an MRC Prodigy Express2 or Prodigy Advance2 system. Works With ANY Brand Loco or DCC Decoder. Plug-N-Play Setup and Operation. Module acts as an interface between the two most popular smartphone apps: WiThrottle for iPhone®,...

For the beginner who needs more sophistication.ProdigyExpress 2 features... 1.6 Amps of Power 28 Accessory Functions Program all CV's Two or Four digit addressing (0-9999 addresses available) Advanced consisting Simultaneously run multiple...

0001325 Throttlepack Handheld 9900/9950 Instruction Manual

ESU 50322 Speaker Monacor Sp6/4SQ, 59mm Round 8 Ohms, for PIKO G/LGB Loks 59mm Round 8 ohm 1-2 Watts for PIKO G/LGB Loks The speaker is specifically selected for use with the LokSound XL decoder. Additionally, the speaker is suitable...

  The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles. All...

 The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles. All...

With its unique design the LokSound 5 Direct DCC can easily replaceboards that provide poor motor control, low volume, or generally inferiorsound. Not only will the decoder work fine with most factory installedspeakers, but it will sound even better with...

  LokSound 5 micro DCC "blank decoder", 8-pin NEM652, gauge: N, TT, H0   The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit...