DCC Accessories

Buy this pack and save on UWT-100 Throttle holders! This holder only fits the UWT-100. Includes: 3 - 3D printed holder designed perfectly for the UWT-100 3 - Bags of 2 Screws

Buy this pack and save on UWT-50/100 Throttle holders! This holder can be used with the UWT-50, LT-50, or UWT-100! Includes: 3 - 3D printed holder designed perfectly for UWT-50, LT-50, and UWT-100 throttles. 3 - Bags of 4 Screws

Works ONLY with the NCE Cab Bus. See WFD-31 for use with NCE Power Cab or CAB Bus Install this Wi-Fi device on your NCE layout to provide Wi-Fi access.  Then use the power of the TCS universal WiFi throttles on your NCE layout to control trains. A...

Works with the NCE Power Cab or Cab Bus. See WFD-30 for use with only NCE Cab Bus Install this Wi-Fi device on your NCE layout to provide Wi-Fi access.  Then use the power of the TCS universal WiFi throttles on your NCE layout to control trains. A...

RJ12 cable with a length of 2 feet. For use with DCC systems such as Digitrax LocoNet.

RJ12 cable with a length of 2 feet. For use with DCC systems such as Digitrax LocoNet.

Control one twin coil "Snap" switch machine. Has capacitive discharge for low current draw of track power. Provides connections for two "local control" pushbuttons. You can control switches from your cabs and your control panels.

SwitchPilot 3 decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption.In order to facilitate the rather cumbersome...

Plug and Play Universal fascia panel supporting LocoNet. Two RJ12 front panel Throttle jacks. Three RJ12 rear pass-through LocoNet jacks Supports throttle charging. Fully connectorized installation. 2mm rear plug for e.g. PS14 DC power supply. 4-pin...

4 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management. Each DS supports Occupancy detection. Each...

Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28 - AWG 12 so there is no problem connecting different wire sizes together. Easily disconnect wiring for trouble...

Servo Extension Cable (M-F) This 39" cable may be used to extend the length of the above (M-M) cables.

Servo Connection Cable (M-M) This 20" cable may be used to connect two Quik-Link devices.

This Breakout board allows easy solder free connections from up to 8 Quik-Link devices to 10 pin I/O cables using 3 wire servo style cables. Also compatible with Berrett Hill products.

The TAB is designed to provide a solder-less connection between the SMD-8 and Tortoise. It includes 10 pin daisy chain cable headers and channel selection jumpers. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. An 8...

The Tortoise Quik-Link is a plug on Tortoise driver board. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. It connects directly to any LCC output port with a standard 10 pin ribbon cable or via a QL-Breakout using a...

This plastic mounting track is suitable for mounting six I/O modules to a flat surface. (3 1/2" x 12")

This plastic mounting track is suitable for mounting four I/O modules to a flat surface. (3 1/2" x 8")

This plastic mounting track is suitable for mounting two I/O modules to a flat surface. (3 1/2" x 4")

This plastic mounting track is suitable for mounting a single I/O module to a flat surface. (3 1/2" x 2")