DCC Accessories

  For use with Digitrax Decoders Equipped with 6 pin Function Harness 8 ohm 10x18 mm Oval speaker included. Keeps locos running during intermittent power interruptions resulting from dirty or bad track. 0.33 F Capacitance Use on...

  For use with Digitrax Decoders Equipped with 6 pin Function Harness 8 ohm 16 x 26 x 9 mm box speaker included Keeps locos running during intermittent power interruptions resulting from dirty or bad track. 0.33 F Capacitance ...

  For use with Digitrax Decoders Equipped with 2 pin PX socket or solder pad connections Keeps locos running during intermittent power interruptions resulting from dirty or bad track. 0.33 F Capacitance Use on 10-18V Track Power Hold...

 The PS14 is a 300ma, 14 Volt power supply for powering Digitrax accessories like the UP5, BDL168, DS64, SE8C, LNRP, UR90, UR91 UR92 and others  Universal AC input 95-240V 50/60Hz  US 2 prong plug, in sideways orientation to fit...

 The PR4 makes decoder programming and interfacing your layout and computer easier than ever. The PR4 seamlessly switches between computer interface and decoder programming modes automatically without having to press any buttons. The PR4 is...

 It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor. LT1 Features: Use as a diagnostic tester Test decoders prior to...

 The LNWI allows you to connect compatible WiFi devices to LocoNet and run trains using compatible throttle apps. The apps available can be downloaded from this page. Wi-Fi interface to a Digitrax LocoNet for up to four compatible mobile Wi-Fi...

 The DT602D is our top-of-the-line, Duplex Radio Super Throttle.  The DT602D Advanced Super Throttle gives you direct control of two locos at a time with all the powerful features and flexibility serious model railroaders demand. The DT602D is...

 The DT602 Advanced super throttle gives you direct control of two locos at a time with all the powerful features and flexibility serious model railroaders demand.  Available in standard tethered or Radio Duplex.   The DT602 is...

  9G mini servo system for turnout or motion control. Under layout mounting bracket included. Compact install for tight N scale switches, and decks. Includes pre-formed drive wires. Supplied with mount hardware.

  Input interconnect board for DS74. Provides plug and play connectivity for DS74 inputs. Supplied with ribbon cable to plug into DS74 10 pin Input header. Allows plug-in of up to 4 DSXCP1 fascia controls. Direct ribbon cable plug-in...

  Quad switch decoder for Solenoid or Slow-motion turnouts. Configurable for Capacitive Discharge with balky solenoids. Configurable for on/off control of 8 layout lights. Plug and play wire connectorization. Works with compatible LocoNet...

 Digitrax 9 pin to DCC medium plug short harness (1”)

Dual 3/5/8 Amp AutoReversing DCC Booster Up to 16 Amps of power total N, HO, & Large Scale Operations with Custom Voltage Trim LocoNet for easy plug ‘n play installation and system expansion Easy dip switch setup Auto resetting over...

Single 3/5/8 Amp AutoReversing DCC Booster (no command station capability) Up to 8 Amps of power total N, HO, & Large Scale Operations with Custom Voltage Trim LocoNet for easy plug ‘n play installation and system expansion Easy dip switch...

 The BXPA1 is a combination DCC Auto-Revereser, occupancy detector, Transponding detector, and intelligent power manager. It is designed to make transponding implementation easy and provide advanced DCC track management by communicating all state...

 BXP88 makes adding detection and transponding to your layout easier than ever.  No more complicated wiring! DCC Occupancy Detection supports up to 8 Detection Sections letting you know when equipped rolling stock is in a detection section...

 AR1 Features: Cost effective automatic reversing for one reversing section or subdistrict User selectable trip current lets you adjust the AR1 to work with any scale or equipment on your layout Auto-Reversing manages polarity...

 Decoder Wire for decoder, lighting & signal installation 90ft 32AWG stranded wire-10 ft lengths in 9 colors

Ideal for constant lighting source in unpowered rolling stock. No ballast lamps or motors required. Will power Mars flasher in models driven by low current can motors. Works with all forms of track power. Max current output is 1/2 amp. Circuitron Multi...