DCC Accessories

4 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management. Each DS supports Occupancy detection. Each...

Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28 - AWG 12 so there is no problem connecting different wire sizes together. Easily disconnect wiring for trouble...

This plastic mounting track is suitable for mounting a single I/O module to a flat surface. (3 1/2" x 2")

Set of 4 CT (Current Transformer) coils for BOD4 or BOD4-CP.

Set of 8 CT (Current Transformer) coils for BOD-8. These 100:1 toroid coils sense the track current on leads passing through the hole in the middle of the coil. They connect to the BOD-8 with twisted pair cable such as CAT-3 or CAT-5 network cable. (up...

(Block Occupancy Detector-4) This board operates as a DCC occupancy detector for 4 blocks using remote CT coils. It outputs logic levels, and has a RR-CirKits standard ribbon connector interface. The "Power-Lok" feature optionally monitors the DCC bus...

A double-pole, double-throw relay with actuating mechanism driven by a momentary-power, twin coil solenoid. (A solenoid is a cylindrical coil of insulated wire in which an iron core is made to move back and forth by a flow of electric current.) With just...

This 13.6mm x 9.6mm speaker could be classified as a "sugar cube" speaker. This style of speaker is often feature in cell phones and tablets and performs slightly differently from standard speakers. This style of speaker REQUIRES mounting with a baffle...

TCS Keep-Alive® (KA) devices are used to supply power to decoders during times of power interruption due to dirty track or problematic track work. Newly-redesigned at half the size of a KA4, the KA2 will power HO or N scale locomotives with approximately...

TCS Keep-Alive® (KA) devices are used to supply power to decoders during times of power interruption due to dirty track or problematic track work. Newly-redesigned and coming in at half the size of a KA3, the KA1 will power HO or N scale locomotives...

Introducing The More Compact CurrentKeeperII! Not all models are made the same, and some are a TIGHT fit for a decoder installation. The CurrentKeeper is now available in two sizes to fit more models and make your installs easier! Keep more of your...

Easily connect a CurrentKeeper or extra capacitor to any SoundTraxx decoder equipped with a 2-pin "Quick Plug" to improve performance over dirty track and switches.

The SoundTraxx CurrentKeeper™ is designed to add additional power capacity to any decoder installation. It can be used to overcome dirty track, limited electrical pickup or dead frogs to ensure reliable operation of any locomotive in your fleet...

The DBX-9000 is a compact 9-wire connector and harness assembly for use with universal-style DCC decoders. It is designed to simplify the wiring connection between a steam locomotive and its tender, providing a quick-disconnect for...

The Decoder Buddy V5 and V5B were developed for the 12 output decoders and include a couple added features. This mother board does not include the 21-Pin Decoder. This mother board requires soldering. This printed circuit board is NOT INTENDED FOR USE IN...

Same six-wire connectors in front as UTP but allows use of off-the-shelf CAT5 cables to connect panel-to-panel at rear. Can be used as a cab bus splitter and also adds the ability to add power to the cab bus for larger layouts.

Build your control panels with greatly simplified wiring. Just connect push buttons to the Mini Panel and use to issue turnout routing macros, individual turnout commands by pushing one button. Set up is easy, just plug in a Pro Cab (sold separately) and...

Add this USB computer interface for computer programming and/or operation of your Power Cab equipped layout. Requires USB cable, computer and railroad computer program such as JMRI Decoder Pro and Panel Pro

13.8v DC Power Supply. 1.3 Amp / 2 amp peak. US approved power supply suitable for PowerCab and other applications. This plugs into the back of panels such as the PCP(PowerCab connection panel) and the UTP-CAT5

Detects DCC current being drawn in a block. Connects to AIU01 or Mini Panel. Isolated so that there is no electrical connection to the track. Needs no external power for most operations, suitable for DCC power up to 20 Amps. Can light up LED or operate...