DCC Accessories

With the abundance of lighting functions and wanting to see and check them before I placed the shell on the frame, I decided I needed a way to see what was happening!  I went to work and prototyped a small connector board with LEDs so I could...

1k ohm resistors The Decoder Buddy was developed for the 8 output decoders. This mother board does not include the 21-Pin Decoder. This mother board requires soldering. This printed circuit board is NOT INTENDED FOR USE IN A DC SYSTEM.  However, if...

1k ohm resistors The Decoder Buddy Mini was developed to fit into smaller steam and diesel applications.  There has also been interest in HOn3 and S-Gauge applications. This mother board does not include the 21 Pin Decoder. This mother board...

The UWT-100 Universal WiFi Throttle from TCS is the new standard in WiFi control for model railroads. This throttle brings a new level of ergonomic comfort and operational convenience to handheld controls. Instead of spending time with your head...

The UWT-50 Universal WiFi Throttle from TCS is the new standard in utility WiFi control for model railroads. This throttle brings a new level of ergonomic comfort and operational convenience to a smaller, more affordable package than the UWT-100...

The UWT-50 Universal WiFi Throttle from TCS is the new standard in utility WiFi control for model railroads. This throttle brings a new level of ergonomic comfort and operational convenience to a smaller, more affordable package than the UWT-100...

Plug and Play Universal fascia panel supporting LocoNet. Two RJ12 front panel Throttle jacks. Three RJ12 rear pass-through LocoNet jacks Supports throttle charging. Fully connectorized installation. 2mm rear plug for e.g. PS14 DC power supply. 4-pin...

4 Power Manager sub-districts. Upgraded replacement for PM42, fully encased. Fully connectorized installation. Each Power sub-district / Detection Section (DS) supports Auto-reverse or Short circuit management. Each DS supports Occupancy detection. Each...

Stranded, 550 MHz, UTP, Pure Bare Copper Wire, 24AWG, 5ft, White.

Stranded, 550 MHz, UTP, Pure Bare Copper Wire, 24AWG, 1ft, White.

Multiple Terminal Block Push-in Wiring Cable connector Quick Cable connector, 2 in, 6 out. No more soldering under the layout. Fits AWG 28 - AWG 12 so there is no problem connecting different wire sizes together. Easily disconnect wiring for trouble...

Servo Extension Cable (M-F) This 39" cable may be used to extend the length of the above (M-M) cables.

Servo Connection Cable (M-M) This 20" cable may be used to connect two Quik-Link devices.

The TAB is designed to provide a solder-less connection between the SMD-8 and Tortoise. It includes 10 pin daisy chain cable headers and channel selection jumpers. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. An 8...

The Tortoise Quik-Link is a plug on Tortoise driver board. Breakaway connector inserts allow use on older Tortoises with narrow paddle contacts. It connects directly to any LCC output port with a standard 10 pin ribbon cable or via a QL-Breakout using a...

This plastic mounting track is suitable for mounting six I/O modules to a flat surface. (3 1/2" x 12")

This plastic mounting track is suitable for mounting four I/O modules to a flat surface. (3 1/2" x 8")

This plastic mounting track is suitable for mounting three I/O modules to a flat surface. (3 1/2" x 6")

(10 position IDC male with latch) Box of 10 Insulation Displacement Connectors for use with 10 wire flat ribbon cable. Use with IDC-S10 to create extension cables. Screw ears allow easy mounting to the layout.

(Fan Out Board, Dual Direct) This board is specifically designed to terminate the dual cable, eight stall motor, connections from a single SMD-8 board. It includes on board jumpers to select common positive or common negative for optional single ended...