DCC Accessories

The new ESU PowerPack Maxi has been developed as the powerful complement to the LokSound L V4.0 /  LokSound  5 L decoder. It can, of course, provided there is sufficient space, also be connected to all LokPilot V4.0, LokSound V4.0, LokSound V4...

Using this adapter board with the dimensions 13.5mm x 8.4mm, Minitrix® locomotives with MTC14 interface can finally be equipped with a LokSound decoder at your own discretion: The adapter board is flexible and is plugged directly into the 14MTC...

This adapter board with the dimensions 54.0mm x 17.0mm has an ESU PowerPack ‘On Board’. Although the capacitors protruding at the front and rear make for a total length of 70mm, this adapter board is ideal for converting many American H0...

This adapter board with dimensions 47.5mm x 14.0mm fits in such Kato (USA) N-gauge locomotives that have a wide body design such as F-units. It replaces the original circuit board and has connection pads for motor and track as well as the function...

The E24 adapter board is suitable if you want to digitize a very small locomotive without a digital interface using the LokSound 5 Nano. With dimensions of only 19.6 mm x 8.5 mm, the board is exactly the same size as the decoder itself and therefore only...

With the help of the BLI Paragon 3/4 (P34) adapter board, H0 Scale tender steam locomotives from Broadway Limited (BLI), in which a Paragon 3 or Paragon 4 decoder was factory installed, can finally be equipped with a LokSound 5 decoder without much...

This adapter board is for owners of a Hübner railbus in track 1 (Art. No. 4070 or 4071) thought. There, a LokSound 2 decoder was installed in the motor car on a special adapter, and in the control car a specially made light change decoder was...

This adapter board ensures the convenient connection of your LokSound 5 L or LokPilot 5 L Decoders. The decoder is inserted directly into the socket strips. On the output side, the most important connections can be contacted directly on robust screw...

If necessary, you can add the Decoder Tester Extension to your Profi Decoder Tester: Plugged into the side of the Decoder Tester it enables you to comfortably test all large scale decoders. If you also have to deal with large scale LokSound XL or...

The Next18 adapter board is suitable if you want to digitize a very small locomotive without a digital interface, but do not want to freely wire the decoder. With dimensions of only 13.0 mm x 9.0 mm, the board is extremely small and also has a...

Adapter board, 18-pin Next-18 socket to Plux16.

Adapter board, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube.

Adapter board, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube

Wire harness, 18-pin Next18 socket to open wires, 88mm, with heat shrink tube

This adapter board can be connected to all decoders with an E24 connection and offers a PluX16 interface on the locomotive side. This means, for example, a LokSound 5 Nano or LokPilot 5 Nano can be easily installed in older locomotives that only provide...

For professionals in digital model railroading there is a new adapter board. This makes installation easier and safer. First all wires are connected to the soldering points of the adapter board. All contact points (terminals) are present on both - top...

With this expansion board you can easily expand your LokPilot or LokSound decoder (with 21MTC interface!): All you need to do is to plug the decoder onto the expansion board and benefit from using 4 additional function outputs (AUX5 through...

The 21 MTC adapter board 2 is also suitable for digitising a loco without interface. It is very helpful, if you do not intend to wire the decoder freely or if you wish to use more than four function outputs on your LokPilot or LokSound decoder. This...

The 21 MTC adapter board is suitable for digitising a loco without interface and for the case you do not intend to wire the decoder freely. The adapter board offers a possibility for installing a decoder with 21MTC connector. This decoder is simply...

Many railcars are equipped with a grinder at both ends. For proper function in block locations and for timely stopping in front of red signals, it is essential that depending on the direction of travel, only one grinder is used to power the decoder. The...