Electronics

Servos, mounting brackets, extension cables, Y cables and reversers and parts to make working with servos easier. As well as the servo decoders on the Tam Valley Depot website, all of the servo products on this page work with all R/C servo controllers...

Servos, mounting brackets, extension cables, Y cables and reversers and parts to make working with servos easier. As well as the servo decoders on the Tam Valley Depot website, all of the servo products on this page work with all R/C servo controllers...

Servos, mounting brackets, extension cables, Y cables and reversers and parts to make working with servos easier. As well as the servo decoders on the Tam Valley Depot website, all of the servo products on this page work with all R/C servo controllers...

You can control your Octopus II or III with the Octocoder, a simple stationary DCC decoder.  The board provides connections os you can also connect fascia controllers and LEDs for local control. (Will not work with toggle switches however.) No...

Remote Aligner for Octopus IIIUsed with the Octopus III (above) for alignment of servos (cannot be used with the Octopus II).  Just one of these needed for all of your Octopus IIIs.  Comes with a 7' cable which allows you to stand next to...

Octopus IIIBoard has 8 positions for driving servos between two positions and 8 inputs for fascia controllers (see below) or toggle switches.  Octopus III uses the remote board (below) to align the servos and has automated endpoint adjustment as...

This adapter mates with the above two power supplies to make them easy to hook up to wires using the screw terminals. Jack size is 5.5/2.1 mm. Plus and minus terminals are marked. Price is for one adapter - picture shows two to illustrate both ends.

This adapter mates with the DCC boster power jack in order to hook up your own power supply using the screw terminals. Plug size is 5.5/2.1 mm. Plus and minus terminals are marked. Price is for one adapter - picture shows two to illustrate both ends.

The ideal power supply for the SwitchWright, this unit is well-regulated and current protected. The unit has a barrel connector that fits the adapter below or you can cut it off and strip the wires. It can support about 30 SwitchWright switch machines...

12V 5A Power Supply for Accessory Bus Use12V 5A 60W switching power supply. Best for powering Quads and Singlets.  Plug size is 5.5/2.1 mm. Power supply comes with a US 110V plug.  By swapping the power cord can be used with...

16V 4.5A Power Supply for Track Power Use16V 4.5A 72W switching power supply - best for track power.  Delivers about 15 V to track when used with our booster above.  Plug size is 5.5/2.1 mm. Power supply comes with a US 110V plug.  By...

5 Amp Trip / 3 A Continuous Duty DCC Booster BoardDCC Booster board without the power supply.  These boards can be used to make locomotive Power Districts or an Accessory District with a shared power supply.  A jumper is used to set...

DCC Mono Frog Juicer (polarity reverser for frogs)For all DCC systems including NCE PowerCab.  This board is an automatic polarity reverser for a single frog.  Setup is simple, connect two wires to the DCC bus and one wire to a frog.  The...

DCC Circuit Breaker Perfect Protection for your Frog Juicers!This is the same board as the Dual Frog Juicer but confugured to work as a circuit breaker.  When there is a short it will cut off both rails at once.  This solves some...

DCC Dual Frog Juicer and Auto-ReverserFor all DCC systems including NCE PowerCab.  This board can be configured to use as an automatic polarity reverser for two frogs, a reversing loop, a turntable, a wye, or a crossing.  It uses the same...

DCC Hex Frog Juicer - power 6 frogsFor DCC systems 2 Amps to 8 Amps including NCE PowerCab.  This board can be configured to use as an automatic polarity reverser for six frogs, or a reverser for one to three reversing loops, turntables, wyes,...

Note: The 60114 or 60112 (1 Gauge) or the 60116 or 60113 (H0) Connector Box is required to connect the Mobile Station. Highlights Simple, easy operation. Background-lighted graphic display with self-explanatory pictograms. Up to 32...

Features: Audio Sync with Environmental Sound Module Pro (purchased separately)  Synchronize up to 8 LEDs to the intensity of the audio for effects like thunderstorms, campfires, welding, etc. Remote External Switch A separate panel mount board can...

The Jackson Railcar Environmental Sound Module Pro adds ambient sounds to your layout! Mount it on your facia and select between 16 different audio sounds that play in a loop. The module comes preloaded with the following sounds:   The user can also...

LocoNet Universal Panel and 3 Amp Z Scale Voltage Reducer 6 LocoNet Jacks for use with all scales Reduces track voltage by 4 or 6 volts at 3 amps for safer Z Scale locomotive operation with Digitrax equipment