DCC Accessories

Remote Aligner for Octopus IIIUsed with the Octopus III (above) for alignment of servos (cannot be used with the Octopus II).  Just one of these needed for all of your Octopus IIIs.  Comes with a...

Octopus IIIBoard has 8 positions for driving servos between two positions and 8 inputs for fascia controllers (see below) or toggle switches.  Octopus III uses the remote board (below) to align...

This adapter mates with the above two power supplies to make them easy to hook up to wires using the screw terminals. Jack size is 5.5/2.1 mm. Plus and minus terminals are marked. Price is for one...

This adapter mates with the DCC boster power jack in order to hook up your own power supply using the screw terminals. Plug size is 5.5/2.1 mm. Plus and minus terminals are marked. Price is for one...

The ideal power supply for the SwitchWright, this unit is well-regulated and current protected. The unit has a barrel connector that fits the adapter below or you can cut it off and strip the wires...

12V 5A Power Supply for Accessory Bus Use12V 5A 60W switching power supply. Best for powering Quads and Singlets.  Plug size is 5.5/2.1 mm. Power supply comes with a US 110V plug.  By swapping

16V 4.5A Power Supply for Track Power Use16V 4.5A 72W switching power supply - best for track power.  Delivers about 15 V to track when used with our booster above.  Plug size is 5.5/2.1 mm. Power...

5 Amp Trip / 3 A Continuous Duty DCC Booster BoardDCC Booster board without the power supply.  These boards can be used to make locomotive Power Districts or an Accessory District with a shared power...

DCC Mono Frog Juicer (polarity reverser for frogs)For all DCC systems including NCE PowerCab.  This board is an automatic polarity reverser for a single frog.  Setup is simple, connect two wires to...

DCC Circuit Breaker Perfect Protection for your Frog Juicers!This is the same board as the Dual Frog Juicer but confugured to work as a circuit breaker.  When there is a short it will cut off both...

DCC Dual Frog Juicer and Auto-ReverserFor all DCC systems including NCE PowerCab.  This board can be configured to use as an automatic polarity reverser for two frogs, a reversing loop, a...

DCC Hex Frog Juicer - power 6 frogsFor DCC systems 2 Amps to 8 Amps including NCE PowerCab.  This board can be configured to use as an automatic polarity reverser for six frogs, or a reverser for one...

LocoNet Universal Panel and 3 Amp Z Scale Voltage Reducer 6 LocoNet Jacks for use with all scales Reduces track voltage by 4 or 6 volts at 3 amps for safer Z Scale locomotive operation with...

Prodigy Advanced & Tech 6 Extension Plate and CablesAllows user to extend the range of two handhelds by more than 9 feet. Plug-in port for mounting around your layout All Cables include RJ45...

EXPAND: Expand your Prodigy DCC layout with a 0001415 Handheld Controller. For use with Prodigy Elite, Prodigy Advanced 2, Prodigy Advance, Prodigy Express2 or Prodigy Express. The 0001415 Handheld...

Decoder Buddy from Nix Trainz is a 21-pin-friendly replacement motherboard for the standard factory-supplied DCC 8-pin loco motherboard in many locomotives. It allows you to take full advantage of...

A 10 foot (120in) length of CAT6a cable. Useable in different applications such as connecting systems or DCC systems to computers.

A 7 foot (84in) length of CAT6a cable. Useable in different applications such as connecting systems or DCC systems to computers.

A 1 foot (60in) length of CAT6a cable. Useable in different applications such as connecting systems or DCC systems to computers.

A 1 foot (36in) length of CAT6a cable. Useable in different applications such as connecting systems or DCC systems to computers.