DCC Accessories

  Keeps locos & sound running during power interruptions caused by dirty or bad track. Hold up time varies based on decoder load & track conditions. Use with Digitrax Series 6 Decoders with 10...

  Keeps locos & sound running during power interruptions caused by dirty or bad track. Hold up time varies based on decoder load & track conditions. PX112-2 Plug ‘N Play Install on DH126 &...

  Keeps locos & sound running during power interruptions caused by dirty or bad track. Hold up time varies based on decoder load & track conditions. Use with Digitrax Series 6 Decoders with 6...

  Keeps locos running during power interruptions caused by dirty or bad track. Keeps light and other functions from dropping out due to power interruptions. Hold up time varies based on...

 RD2 Remote Sensing Diodes for BDL16 series occupancy detectorsRemote sensing of 2 detection sections. Eliminates the need for long runs of heavy gauge wire between the BDL168, BDL16 & BDL162 and...

 The PR4 makes decoder programming and interfacing your layout and computer easier than ever. The PR4 seamlessly switches between computer interface and decoder programming modes automatically...

 The PS14 is a 300ma, 14 Volt power supply for powering Digitrax accessories like the UP5, BDL168, DS64, SE8C, LNRP, UR90, UR91 UR92 and others  Universal AC input 95-240V 50/60Hz  US 2 prong...

 PS615 90W AC/DC 15VDC 6 amp power supply for use with all Digitrax Command Stations and Boosters operating at 5 amps. High-efficiency power supply 15 VDC output Accepts different cord sets ...

  For use with Digitrax Decoders Equipped with 2 pin PX socket or solder pad connections Keeps locos running during intermittent power interruptions resulting from dirty or bad track. 0.33 F...

  For use with Digitrax Decoders Equipped with 6 pin Function Harness 8 ohm 16 x 26 x 9 mm box speaker included Keeps locos running during intermittent power interruptions resulting from...

  For use with Digitrax Decoders Equipped with 6 pin Function Harness 8 ohm 10x18 mm Oval speaker included. Keeps locos running during intermittent power interruptions resulting from dirty or...

 The LNWI allows you to connect compatible WiFi devices to LocoNet and run trains using compatible throttle apps. The apps available can be downloaded from this page. Wi-Fi interface to a Digitrax...

 It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor. LT1 Features: Use as a diagnostic...

 The DT602D is our top-of-the-line, Duplex Radio Super Throttle.  The DT602D Advanced Super Throttle gives you direct control of two locos at a time with all the powerful features and flexibility...

  Quad switch decoder for Solenoid or Slow-motion turnouts. Configurable for Capacitive Discharge with balky solenoids. Configurable for on/off control of 8 layout lights. Plug and play wire...

  Input interconnect board for DS74. Provides plug and play connectivity for DS74 inputs. Supplied with ribbon cable to plug into DS74 10 pin Input header. Allows plug-in of up to 4 DSXCP1...

  9G mini servo system for turnout or motion control. Under layout mounting bracket included. Compact install for tight N scale switches, and decks. Includes pre-formed drive wires. ...

 The DT602 Advanced super throttle gives you direct control of two locos at a time with all the powerful features and flexibility serious model railroaders demand.  Available in standard tethered or...

 Digitrax 9 pin to DCC medium plug short harness (1”)

 BXP88 makes adding detection and transponding to your layout easier than ever.  No more complicated wiring! DCC Occupancy Detection supports up to 8 Detection Sections letting you know when...