ESU

The LokPilot 5 L finds its place wherever the LokPilot 5 no longer “fits” in terms of performance. Ideally, these are vehicles of nominal size 0, but also gauge 1 vehicles that are to be...

The LokPilot 5 L finds its place wherever the LokPilot 5 no longer “fits” in terms of performance. Ideally, these are vehicles of nominal size 0, but also gauge 1 vehicles that are to be...

The LokSound 5 XL decoder is quite a big piece of equipment. It has to be, because it is intended for use in large scale model railways, e.g. garden railways and 1 gauge models. Its integral...

The LokSound 5 XL decoder is quite a big piece of equipment. It has to be, because it is intended for use in large scale model railways, e.g. garden railways and 1 gauge models. Its integral...

LokSound 5 L is intended for use in all applications where the required power exceeds the limits of LokSound 5.  Ideally these are 0 gauge vehicles and also smaller 1 gauge locomotives...

LokSound 5 L is intended for use in all applications where the required power exceeds the limits of LokSound 5.  Ideally these are 0 gauge vehicles and also smaller 1 gauge locomotives...

The new ESU PowerPack Maxi has been developed as the powerful complement to the LokSound L V4.0 /  LokSound  5 L decoder. It can, of course, provided there is sufficient space, also be...

Using this adapter board with the dimensions 13.5mm x 8.4mm, Minitrix® locomotives with MTC14 interface can finally be equipped with a LokSound decoder at your own discretion: The adapter board...

This adapter board with the dimensions 54.0mm x 17.0mm has an ESU PowerPack ‘On Board’. Although the capacitors protruding at the front and rear make for a total length of 70mm, this...

This adapter board with dimensions 47.5mm x 14.0mm fits in such Kato (USA) N-gauge locomotives that have a wide body design such as F-units. It replaces the original circuit board and has connection...

The E24 adapter board is suitable if you want to digitize a very small locomotive without a digital interface using the LokSound 5 Nano. With dimensions of only 19.6 mm x 8.5 mm, the board is exactly...

With the help of the BLI Paragon 3/4 (P34) adapter board, H0 Scale tender steam locomotives from Broadway Limited (BLI), in which a Paragon 3 or Paragon 4 decoder was factory installed, can finally...

This adapter board is for owners of a Hübner railbus in track 1 (Art. No. 4070 or 4071) thought. There, a LokSound 2 decoder was installed in the motor car on a special adapter, and in the...

This adapter board ensures the convenient connection of your LokSound 5 L or LokPilot 5 L Decoders. The decoder is inserted directly into the socket strips. On the output side, the most important...

Thin cables Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to...

Thin cables Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to...

If necessary, you can add the Decoder Tester Extension to your Profi Decoder Tester: Plugged into the side of the Decoder Tester it enables you to comfortably test all large scale decoders. If...

The Next18 adapter board is suitable if you want to digitize a very small locomotive without a digital interface, but do not want to freely wire the decoder. With dimensions of only 13.0 mm x 9...

Adapter board, 18-pin Next-18 socket to Plux16.

Adapter board, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube.