Electronics

The MP-15N is a N-scale drop-in decoder which is designed for the Atlas MP-15 locomotive. See the installation pages for a full list of compatible engines! Back EMF Load Compensation: Provides superior slow speed control and high performance...

This custom-designed holder can hold a single TCS throttle such as the UWT-50, LT-50, or UWT-100! Includes: 1 - 3D printed holder designed perfectly for UWT50, LT-50, and UWT-100. 1 - Bag of 4 Screws

TCS Keep Alive® (KA) devices are used to supply power to decoders during times of power interruption due to dirty track or problematic track work. The WAX-KA3 will power an HO-Scale locomotive with headlights on for approximately 6 to 20 seconds...

The K0D8-F is a N-scale drop-in decoder designed specifically for the Kato FP7A locomotive. Note: The K0D8 line of decoders are available with different lighting configurations. Pay special attention to the compatibility. The...

For Intermountain N scale FT B units with motor contact "shoes" 6 FX3 Functions .472” x 2.165” x .098”11.98mm x 54.99mm x 2.4 mm Replaces DN163I1B   ▪FX3 Function outputs for prototypical lighting effects and on/off...

For Intermountain N scale F3 and F7 A & B units with motor contact "shoes" 6 FX3 Functions .472” x 2.165” x .098”11.98mm x 54.99mm x 2.4 mm Replaces DN163I1C   ▪FX3 Function outputs for prototypical lighting...

SP28288 - Round 28mm 8 Ohm Speaker with wires.Great for HO installations. Used on current production SFX0416 sound and function decoder. Digitrax recommends the use of a baffle or speaker enclosure with this speaker for maximum sound output.

With our small relay, loads are controllable whose draw exceeds the decoder’s function output. Put the relay between output and load.

 The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles. All...

Speakers for model trains

The Tech 6 Handheld plugs into the Tech 6 Sound Controller to give you the freedom to walk around your layout while operating your trains. It also permits the control of up to 6 decoder-equipped locomotives from this one handheld...

Prodigy Advanced & Tech 6 Extension Plate and CablesAllows user to extend the range of two handhelds by more than 9 feet. Plug-in port for mounting around your layout All Cables include RJ45 connectors - Plug and Play Ready for mounting - Screws...

Plug in 4 function decoder with 6 pin NEM 651 connector Dimensions: 2.65 X 8.77 mm Includes pins 19.41 mm

2-wire stay alive device compatible with Tsunami2 and TCS decoders.

This snap-together baffle kit is designed for use with our 15mm round speakers (P.N. 810089).

If you have more space, this speaker is great for larger models. Dimensions: 35 x 20 x 5.3mm(D)Frequency Response: 560Hz - 20kHzPower: 1 Watt (Nominal) 2 Watts (Peak)Impedance: 8 Ohms

A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer...

A true pioneer in the model train industry, SoundTraxx has been creating innovative products for the discriminating model railroader since 1990. We proudly design and manufacture our industry-best products right here in the USA, and our friendly customer...

Servos, mounting brackets, extension cables, Y cables and reversers and parts to make working with servos easier. As well as the servo decoders on the Tam Valley Depot website, all of the servo products on this page work with all R/C servo controllers...