Electronics

This RGY LED is provided with four 24" long color coded #36 AWG wires. It may be fitted in place of a common T-1 LED with room to spare. The LED provides the three standard searchlight signal colors and is wired the same as a normal three light signal...

This board is normally used for block detection on three rail layouts. This version of the board includes internal current limiters. Useful anyplace that an external voltage needs to be monitored. (5V-20V AC-DC-DCC)

Relay Board - 4 is a Quad 10A SPDT relay board with logic level drivers. It is suitable for use with TC Mark II, TowerMan, Tower LCC, or other logic level output devices. It requires 12V auxiliary power to supply the relay coils. Auxiliary power is...

(Single Coil Solenoid Driver) This 8 line, optically isolated, single ended, high current, high voltage DC driver can drive up to 1A continous per line at up to 30VDC. When used with custom Tower LCC settings and a CD power supply this board will drive 4...

(Stall Motor Driver) LCC sample mode compatible. This 8 output, optically isolated, low current "H" bridge driver is designed for control of 8 stall motor switch machines. (E.g. Tortoises®) It can drive up to 100ma. per line, speed regulated output 6 to...

(I/O Test Board) This board contains 8 push button switches and 8 LED pairs. It is designed to quickly test the I/O ports on any of our boards such as the Tower LCC, Mark II, various of the WorkMan series SSB boards, and our LCC I/O nodes. It may be...

Single CT (Current Transformer) coil.

Set of 4 CT (Current Transformer) coils for BOD4 or BOD4-CP.

Set of 8 CT (Current Transformer) coils for BOD-8. These 100:1 toroid coils sense the track current on leads passing through the hole in the middle of the coil. They connect to the BOD-8 with twisted pair cable such as CAT-3 or CAT-5 network cable. (up...

(Block Occupancy Detector-4) This board operates as a DCC occupancy detector for 4 blocks using remote CT coils. It outputs logic levels, and has a RR-CirKits standard ribbon connector interface. The "Power-Lok" feature optionally monitors the DCC bus...

(Block Occupancy Detector-8 - SM) This new board is compatible with LCC node sample mode which allows using output drivers on the same I/O port. This board operates as a DCC occupancy detector for 8 blocks using remote CT coils. It outputs logic levels,...

USB to serial Interface unit. Includes driver disk.  Well suited for interfacing NCE Power Pro command station to USB. This unit does not require any modifications to the command station for proper attachment.  Note: Not for Power Cab,...

16 Led drivers plus 8 line Input/Output node for NMRA CAN bus LCC®. Logic level I/O port compatible with other standard RR-CirKits I/O modules. Boot Loader for user installable firmware upgrades.  Includes powerful internal Logic Elements...

16 Led drivers plus 8 line Input/Output node for NMRA CAN bus LCC®. Logic level I/O port compatible with other standard RR-CirKits I/O modules. Boot Loader for user installable firmware upgrades. Includes powerful internal Logic Elements. Compatible with...

LCC Starter Kit Includes: LCC Buffer-USB Power-Point 2 Terminators 1' LCC cable and USB cable

LCC Buffer-USB Features:  • NMRA CAN bus LCC® to USB interface.  • 2,500 Volt High Speed Digital isolation between CAN bus LCC® and USB port.  • Simplify your LCC configuration and/or use a PC based CTC.  • Compatible with JMRI...

The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a...

The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a...

The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a...

The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot...